{"EX00001.json": {"dateRaised": 20190101, "affectedFirmware": ["plane"], "hardwareLimited": [], "description": "This is an example open issue for Plane only, V3.9.5 and above", "mitigation": "Put the temporary mitigation here", "fixCommit": [], "dateResolved": null, "linkedIssue": "https://github.com/ArduPilot/ardupilot/issues", "linkedInfo": ["www.ardupilot.com", "https://discuss.ardupilot.club/"], "linkedPR": null, "versionFrom": {"plane": "3.9.5"}, "versionFixed": {}, "criticality": 3, "lastmodified": "2020-10-04T20:41:07+11:00"}, "EX00003.json": {"dateRaised": 20190624, "affectedFirmware": ["all"], "hardwareLimited": [], "description": "Another example that is only resolved for plane and copter, other firmwares outstanding", "mitigation": "Do something else until a fixed firmware is released", "fixCommit": ["f8cfbb8062d097aece56df4fb271818264c5699f", "f8cfbb8062d097aecs56df46b271818264c5699f"], "dateResolved": 20190825, "linkedIssue": "https://github.com/ArduPilot/ardupilot/issues/9999", "linkedInfo": ["www.google.com", "www.bing.com"], "linkedPR": "https://github.com/ArduPilot/ardupilot/pull/8888", "versionFrom": {}, "versionFixed": {"copter": "3.5.11", "plane": "3.9.4"}, "criticality": 4, "lastmodified": "2020-10-04T20:41:07+11:00"}, "EX00002.json": {"dateRaised": 20190210, "affectedFirmware": ["all"], "hardwareLimited": ["Pixhawk1-1M"], "description": "This is an example issue that only affects the Pixhawk1-1M boards", "mitigation": "Do something", "fixCommit": ["f8cfbb8062d097aece56df46b271818264c5699f"], "dateResolved": 20190410, "linkedIssue": "https://github.com/ArduPilot/ardupilot/issues/11642", "linkedInfo": [], "linkedPR": "https://github.com/ArduPilot/ardupilot/pull/12125", "versionFrom": {}, "versionFixed": {"copter": "9.6.11", "plane": "9.9.11", "rover": "9.5.0", "sub": "9.5.2", "antenna": "9.5.2"}, "criticality": 2, "lastmodified": "2020-10-04T20:41:07+11:00"}, "EX00004.json": {"dateRaised": 20190624, "affectedFirmware": ["all"], "hardwareLimited": [], "description": "Interference from an external cable connected to the I2C bus may cause a flood of interrupts on the Flight Controller, locking it up", "mitigation": "Do not use I2C devices where possible. Ensure all I2C cables are short in length and not near any RF noise sources", "fixCommit": ["f8cfbb8062d097aece56df46b271818264c5699f"], "dateResolved": 20190824, "linkedIssue": "https://github.com/ArduPilot/ardupilot/issues/11642", "linkedInfo": [], "linkedPR": "https://github.com/ArduPilot/ardupilot/pull/12125", "versionFrom": {}, "versionFixed": {"copter": "3.6.11", "plane": "3.9.11", "rover": "3.5.2", "sub": "3.5.3", "antenna": "0.7.2"}, "criticality": 1, "lastmodified": "2020-10-04T20:41:07+11:00"}, "EX00005.json": {"dateRaised": 20200110, "affectedFirmware": ["copter", "plane", "rover"], "hardwareLimited": [], "description": "If FrSky SPort Passthrough is enabled on a Telemetry port, a race condition may cause an in-air lockup of the Autopilot", "mitigation": "Disable FrSky SPort Passthrough by setting the SERIALx_PROTOCOL parameters to anything but 10.", "fixCommit": ["36122c881ea05f84583d2a002424f3984804f20c"], "dateResolved": 20200110, "linkedIssue": null, "linkedInfo": ["https://discuss.ardupilot.club/t/critical-issue-with-frsky-sport-passthrough-telemetry-in-4-0-x-releases/50967", "https://discuss.ardupilot.club/t/hexa-crash-after-watchdog-reset/50917"], "linkedPR": "https://github.com/ArduPilot/ardupilot/pull/13217", "versionFrom": {"copter": "4.0.0", "plane": "4.0.0", "rover": "4.0.0"}, "versionFixed": {"copter": "4.0.1", "plane": "4.0.3"}, "criticality": 3, "lastmodified": "2020-10-04T20:41:07+11:00"}}